=pod
{- OpenSSL::safe::output_do_not_edit_headers(); -}

=head1 NAME

openssl-fipsinstall - perform FIPS configuration installation

=head1 SYNOPSIS

B<openssl fipsinstall>
[B<-help>]
[B<-in> I<configfilename>]
[B<-out> I<configfilename>]
[B<-module> I<modulefilename>]
[B<-provider_name> I<providername>]
[B<-section_name> I<sectionname>]
[B<-verify>]
[B<-mac_name> I<macname>]
[B<-macopt> I<nm>:I<v>]
[B<-noout>]
[B<-quiet>]
[B<-corrupt_desc> I<selftest_description>]
[B<-corrupt_type> I<selftest_type>]

=head1 DESCRIPTION

This command is used to generate a FIPS module configuration file.
This configuration file can be used each time a FIPS module is loaded
in order to pass data to the FIPS module self tests. The FIPS module always
verifies its MAC, but only needs to run the KAT's once,
at installation.

The generated configuration file consists of:

=over 4

=item - A MAC of the FIPS module file.

=item - A test status indicator.

This indicates if the Known Answer Self Tests (KAT's) have successfully run.

=item - A MAC of the status indicator.

=back

This file is described in L<fips_config(5)>.

=head1 OPTIONS

=over 4

=item B<-help>

Print a usage message.

=item B<-module> I<filename>

Filename of the FIPS module to perform an integrity check on.

=item B<-out> I<configfilename>

Filename to output the configuration data to; the default is standard output.

=item B<-in> I<configfilename>

Input filename to load configuration data from. Used with the B<-verify> option.
Standard input is used if the filename is C<->.

=item B<-verify>

Verify that the input configuration file contains the correct information.

=item B<-provider_name> I<providername>

Name of the provider inside the configuration file.
This must be specified.

=item B<-section_name> I<sectionname>

Name of the section inside the configuration file.
This must be specified.

=item B<-mac_name> I<name>

Specifies the name of a supported MAC algorithm which will be used.
The MAC mechanisms that are available will depend on the options
used when building OpenSSL.
To see the list of supported MAC's use the command
C<openssl list -mac-algorithms>.  The default is B<HMAC>.

=item B<-macopt> I<nm>:I<v>

Passes options to the MAC algorithm.
A comprehensive list of controls can be found in the EVP_MAC implementation
documentation.
Common control strings used for this command are:

=over 4

=item B<key>:I<string>

Specifies the MAC key as an alphanumeric string (use if the key contains
printable characters only).
The string length must conform to any restrictions of the MAC algorithm.
A key must be specified for every MAC algorithm.
If no key is provided, the default that was specified when OpenSSL was
configured is used.

=item B<hexkey>:I<string>

Specifies the MAC key in hexadecimal form (two hex digits per byte).
The key length must conform to any restrictions of the MAC algorithm.
A key must be specified for every MAC algorithm.
If no key is provided, the default that was specified when OpenSSL was
configured is used.

=item B<digest>:I<string>

Used by HMAC as an alphanumeric string (use if the key contains printable
characters only).
The string length must conform to any restrictions of the MAC algorithm.
To see the list of supported digests, use the command
C<openssl list -digest-commands>.
The default digest is SHA-256.

=back

=item B<-noout>

Disable logging of the self tests.

=item B<-quiet>

Do not output pass/fail messages. Implies B<-noout>.

=item B<-corrupt_desc> I<selftest_description>,
B<-corrupt_type> I<selftest_type>

The corrupt options can be used to test failure of one or more self tests by
name.
Either option or both may be used to select the tests to corrupt.
Refer to the entries for B<st-desc> and B<st-type> in L<OSSL_PROVIDER-FIPS(7)> for
values that can be used.

=back

=head1 EXAMPLES

Calculate the mac of a FIPS module F<fips.so> and run a FIPS self test
for the module, and save the F<fips.cnf> configuration file:

 openssl fipsinstall -module ./fips.so -out fips.cnf -provider_name fips \
         -section_name fipsinstall -mac_name HMAC -macopt digest:SHA256 \
         -macopt hexkey:000102030405060708090A0B0C0D0E0F10111213

Verify that the configuration file F<fips.cnf> contains the correct info:

 openssl fipsinstall -module ./fips.so -in fips.cnf  -provider_name fips \
          -section_name fips_install -mac_name HMAC -macopt digest:SHA256 \
          -macopt hexkey:000102030405060708090A0B0C0D0E0F10111213 -verify

Corrupt any self tests which have the description C<SHA1>:

 openssl fipsinstall -module ./fips.so -out fips.cnf -provider_name fips \
         -section_name fipsinstall -mac_name HMAC -macopt digest:SHA256 \
         -macopt hexkey:000102030405060708090A0B0C0D0E0F10111213 \
         -corrupt_desc 'SHA1'

=head1 SEE ALSO

L<fips_config(5)>,
L<OSSL_PROVIDER-FIPS(7)>,
L<EVP_MAC(3)>

=head1 COPYRIGHT

Copyright 2019-2020 The OpenSSL Project Authors. All Rights Reserved.

Licensed under the Apache License 2.0 (the "License").  You may not use
this file except in compliance with the License.  You can obtain a copy
in the file LICENSE in the source distribution or at
L<https://www.openssl.org/source/license.html>.

=cut